You can also combine different color powders for a truly customized look. Heat is applied to melt the powder that cools as a hard film, enclosing the bullets.

You will have to experiment to find the right shaker container, the amount of paint needed, etc. Johnny’s Reloading Bench, Best 9mm Ammo 2019 [Self-Defense & Target], 6.5 Creedmoor vs .243 Win – Cartridge Comparison, Best .40 S&W Ammo: Self Defense & Target Practice.

That’s it. Pretty simple. If you are using a plastic tumbling container, the type that seems work best and creates the most static electricity (which helps the paint adhere to the bullet) has a recycle triangle on the bottom with the number five. The paint does not crack or peel off when sizing bullets.

The shiny finish shows that the powder has melted and cured on these 7mm bullets. +9. The increased thickness made me leery of the coating; it might have filled crimp grooves enough to prevent applying a sufficient case mouth crimp on bullets to keep them in place during hard recoil.

I then use a brush to remove all the remaining “clinging” paint from the cardboard into the container.

It is a place to teach, to learn, and to collaborate and interact. I was a skeptic at first, but now I coat all my cast bullets. When finished with the process, empty the excess paint back into the tumbling container by simply folding the carboard lengthwise to make a funnel of sorts and channeling/tapping the paint into the container. Diameter increased to .311 inch with one coat of powder. Comparison Test Of Four Eastwood Powder Coats For Cast Bullets Another plus is that cast bullets you make can be very accurate, versatile and useful. They are cheap to set up for and make, very effective, allow easy barrel clean-up, and produce little to no smoke from bullet lube – what’s not to like? Once pushed past about 1000 f.p.s., you start to see strips and flakes of lead in the barrel. Full wadcutters for targets or defense, semi-wadcutters for hunting, round nose to feed in autoloaders…with powder coated bullets you can up the velocity a bit, avoid most leading and have different-colored bullets for specific rounds. for your needs, but this is what works for me.

This adhesion of powder to bullets relies on electricity, just like the powder coating gun. Obviously, it’s hot, so wear gloves! References: Don’t try to do too many-a moderate number of bullets is best. Powder can be applied to bullets by several methods, from complicated to quick. Nothing is freer of contaminates than freshly cast bullets, or bullets stored in a sealed container. Powder coating cast bullets can be expensive or economical. He began creating YouTube videos in 2017, and built The Reloaders Network in 2018. I try to waste as little as possible. I can’t remember the number of deer I’ve taken over the years (not to mention squirrels, with the right load) with my .44 and .45 cast bullets. The oven rack holds an 8.5-inch square pan with some room to spare.

Cast bullets are made from pouring a molten lead alloy mix into a bullet mold. After 10 shots, the borescope showed slight streaks of lead in a few spots in the bore.

The driving band diameter was .310 inch of as-cast RCBS 30-150-CM bullets. Some folks use tweezers to pick up each bullet and set it in a pan, which is time consuming. Leading is a pain to remove, whether it involves a trip to a gunsmith or not. Gently turning a container end over end from a few to five minutes evenly coated bullets. Mike has been a shooter, bullet caster and reloader for over 40 years.

(My bullets come from plain old wheel weights that a friendly tire shop is glad to get rid of.) 11FS powder. Simply tumbling bullets and powder together in a container turned out the cheapest and easiest way to coat bullets evenly. Bullets must be clean for the powder to stick. I’ve read everything from 400 degrees for 20 minutes to 300 degrees at half that time.

A quick explanation…all lead bullets are not necessarily cast bullets. After firing 20-some coated bullets through the .45, its bore was only slightly fouled, probably with primer residue. Elmer Keith blew up a few guns developing his heavy .44 Special loads which evolved into the .44 Magnum.

Cast bullets are made from pouring a molten lead alloy mix into a bullet mold. Whether the bullets are standing up or laying on their side does not affect how evenly the powder cures. Wearing latex gloves and picking out bullets is slightly faster, but touching the bullets in any way removes some powder. The plain ol’ Harbor Freight paints work for me.

“Bake” for 20 minutes at 400 degrees. You can find more information, links to all of his online content, and opportunities to support him if so desired on his Author Page. I shot 20-some of these bullets through a .30-30 at a velocity of 1,267 fps. This is applied to the bullet and it is baked on.

There are other brands of powdered paint out there that have different adherence capabilities, other colors, etc. I have good results when coating between 50-100 bullets, depending on bullet size. Wolfe Publishing Company | 2180 Gulfstream Suite A | Prescott, AZ 86301. (ft. Savage model 64). Shooter’s Coffee Chat: My Start to Casting. One coat applied to all bullets and baked for 20 min. My experience shows that the Lee tumble-lube bullets work best, with their many small driving bands, but other bullets work as well.

Epoxy coatings and Powder coatings. The gun blows negatively charged powder onto positively charged bullets. Some guys will put small plastic Airsoft balls in the shaker container with the bullets to add to the static electricity, or even use some type of spray gun to spray the powder onto the bullets…I’ve never found these processes necessary. The epoxy coating is typically a two part coating that is mixed and applied to the bullet prior to baking it onto the bullet. Pet Loads and Handloader are registered trademarks of Wolfe Publishing Company. Suggestions for oven temperature settings and baking time vary. BONUS OFFER: Get your 500 Page Ammo Comparison Handbook (worth $43) for FREE right into your inbox.

Shake, rattle & roll the container in a circular motion for a minute or two to coat the bullets evenly. Two coats of Harbor Freight red powder put a .003-inch-thick coat on the forward section of RCBS 7mm-145-SIL bullets, making the bullets too wide to fit in new 7mm-08 rifles. If the work of preparing cast bullets is pleasant and pleasurable for you, then the powder-coating process is a good investment of time and small expense of about $30. The benefits are worth the time and investment. The finish on the bullets was slippery, and the bullets easily pushed in and out of a .309-inch sizer die. All that is really required is powder, a plastic container, protective gloves and a mask. They are It is economical, as well…the whole set-up to get started cost me about $40, and ongoing costs are minimal. Some of the NOE 453-210-RF bullets were shot from a .45 Auto into a stack of dry newspapers, and most of the coating remained on the shanks of the recovered bullets. To put that worry to rest, I applied two coats of Harbor Freight Red Powder to bullets cast from an LBT 358-200-FN mould and crimped the bullets in .357 Magnum cases over 14.0 grains of Accurate No.

I find It doesn’t take much paint…a thin, even coat is best. (adsbygoogle = window.adsbygoogle || []).push({}); The Reloaders Network focuses on firearms, shooting sports, reloading, bullet casting, and the related gear and accessories.

A borescope showed no streaks of lead in the bore. Whatever oven you use needs to be able to get to 400 degrees for 20 minutes…that’s all it takes. You may then dump them onto that hard surface to cool, or leave them in the tray once all have been loosened. Powder coating cast bullets can be expensive or economical.

Elvis Ammo Perhaps the coating does protect a bullet’s base somewhat from powder gas, but I’ve never seen where the plain base of cast bullets ever melted from the heat of powder gas. This method requires standing bullets upright with enough space between them to spray an even coat all around the bullets, but leaves the bullets’ bases uncoated.

I left one cartridge unfired in the cylinder while firing ten rounds. It was finally determined that the melted bullets had been directly over the heating element. The bullets at right have two coats.